Bryant 4-Way Multipoise Fixed-Capacity Direct-Vent Conden Manuale Utente Scaricare il pdf (Pagina 15)

A02204b

11 NO PREVIOUS CODE – Stored codes

are erased after 72 hours. On RED LED

boards stored status codes can also be

erased whenever power (115V or 24V)

is interrupted. Run system through a

heating or cooling cycle to check system.

12 BLOWER ON AFTER POWER UP –

(115V OR 24V) – Normal operation.

Blower runs for 90 seconds, if unit is

powered up during a call for heat (R-W

closed) or when (R-W opens) during the

blower on-delay period.

13 LIMIT CIRCUIT LOCKOUT – Lockout

occurs if the limit or flame rollout switch is

open longer than 3 minutes. Control will

auto-reset after 3 hours. See code 33.

14 IGNITION LOCKOUT – System failed to

ignite gas and prove flame in 4 attempts.

Control will auto-reset after 3 hours.

See status code 34.

21 GAS HEATING LOCKOUT – Turn off

power and wait 5 minutes to retry.

Check for:

- Stuck closed gas valve relay on control.

- Miswire or short to gas valve wire.

22 ABNORMAL FLAME-PROVING SIGNAL

Flame is proved while gas valve is de-

energized. Inducer will run until fault is

cleared. Check for:

- Stuck open or leaky gas valve.

23 PRESSURE SWITCH DID NOT OPEN

Check for:

- Obstructed pressure tube.

- Pressure switch stuck closed.

24 SECONDARY VOLTAGE FUSE IS OPEN

Check for:

- Short circuit in secondary voltage (24V)

wiring including thermostat leads.

Disconnect thermostat leads to isolate

short circuit.

31 PRESSURE SWITCH DID NOT CLOSE

OR REOPENED – If open longer than 5

minutes, inducer shuts off for 15 minutes

before retry. If opens during blower on-

delay period, blower will come on for the

selected blower off-delay. Check for:

- Proper vent sizing.

- Low inducer voltage (115V).

- Low inlet gas pressure (if LGPS used).

- Inadequate combustion air supply.

- Disconnected or obstructed pressure

tubing.

- Defective inducer motor.

- Defective pressure switch.

- Excessive wind.

- Restricted vent.

33 LIMIT CIRCUIT FAULT – Indicates the

limit or flame rollout switch is open. Blower

will run for 4 minutes or until open switch

remakes whichever is longer. If open

longer than 3 minutes, code changes to

lockout #13. If open less than 3 min.

status code #33 continues to flash until

blower shuts off. Flame rollout switch

requires manual reset. Check for:

- Dirty filter or restricted duct system.

- Loose blower wheel.

- Defective switch or connections.

- Defective blower motor or capacitor.

- Inadequate combustion air supply

(flame rollout switch open).

- Restricted vent.

- Proper vent sizing.

- Excessive wind.

- Blower motor on incorrect speed tap.

- Input rate to furnace set too high.

34 IGNITION PROVING FAILURE – If flame

is not sensed during the trial for ignition

period, the control will repeat the ignition

sequence 3 more times before lockout

#14 occurs. If flame signal is lost during

the blower on-delay period, blower will

come on for the selected blower off-delay.

Check the following items first before

proceeding to the next step.

- Gas valve turned off.

- Manual shut-off valve.

- Green/Yellow wire MUST be connected

to furnace sheet metal.

- Flame sensor must not be grounded.

To determine whether the problem is in

the gas valve, igniter, or flame sensor the

system can be operated in the component

test mode to check the igniter. First

remove the R thermostat connection from

the control and initiate the component

test sequence. Does the igniter glow

orange/white by the end of the 15 second

warm-up period?

Unplug igniter harness from control and initiate

another component test sequence. Check

for 115V between pin 1 and NEUTRAL-L2 on

the control. Was 115V present for the 15

second period?

Reconnect the R thermostat lead and set

thermostat to call for heat. Connect voltmeter

across gas valve connections. Does gas valve

receive 24V?

Does gas valve open and allow gas to flow?

Do the main burners ignite?

Do the main burners stay on?

Repeat call for heat and check flame sensor

current during trial for ignition period. Is the

DC microamps below 0.5?

Is current near typical value?

Will main burners ignite and stay on?

Fixed.

Clean flame sensor with fine steel wool and

recheck current. Nominal current is 4.0 to 6.0

microamps.

45 CONTROL CIRCUITRY LOCKOUT

Auto-reset after 1 hour lockout due to:

- Flame circuit failure.

- Gas valve relay stuck open.

- Software check error.

Reset power to clear lockout. Replace

control if code repeats.

Replace furnace control.

Check for continuity in the harness and igniter.

Replace defective component.

Check connections. If OK, replace control.

Check that all gas valves are turned on.

Replace valve.

Check for:

- Inadequate flame carryover or rough

ignition.

- Low inlet gas pressure.

- Proper firing rate.

- Check for air leakage around igniter bracket.

Allow blower to come on and repeat test to

check for intermittent operation.

Check connections and retry. If current is

near typical value (4.0-6.0 nominal) and

burners will not stay on, replace control.

Replace electrode.

Replace furnace control.

YES

—15—

1 2 ... 10 11 12 13 14 15 16

Commenti su questo manuale

Nessun commento

Bryant 4-Way Multipoise Fixed-Capacity Direct-Vent Conden Manuale Utente Pagina 15

Commenti su questo manuale

Prodotti e manuali riguardandi Forno Bryant 4-Way Multipoise Fixed-Capacity Direct-Vent Conden